Refurbished Products – Filabot

Refurbished Products

  • Sale
  • Regular price €1.750,95

These units are a great way to get started with filament extrusion. All refurbished equipment goes thought mechanical verification. Enclosures and mechanical parts may show some wear and have scratches or dents that otherwise do not effect the quality of extrusion. Consider these units as broken in. They may have a few dents or scratches but the inside is as good as new. These systems come with a 365-day warranty. For any information about the specific equipment please refer to the corresponding product listings. Filabot EX2, Filabot EX2, Filabot Spooler, MDPH2, MDPE10 

Please note that we may not always have a refurbished system in stock and it is first come first serve when they are available.

Refurbished systems can't be applied to bundles nor can they be any further discounted.

The Filabot EX2 system is our mid-level  extrusion system. The EX2 features a three-stage extrusion screw made from hardened and polished high-carbon steel. This proprietary, patent-pending screw  is designed to pressurize plastics during the extrusion process, assisting in diameter control and boosting the overall output. The mixing capability of the screw is enhanced by the utilization of a progressive compression section, which applies shear force between the polymer and the barrel wall. The EX2 also features extrusion speed control. The speed control board includes an automatic, variable voltage control module that is engineered to regulate the precise RPM of the screw as forces fluctuate in the extrusion process. When used with the Filabot Spooler, tolerances of +/-0.05mm can be achieved at a rate of 2 lbs an hour.

The Filabot EX6 extruder is our professional level system, designed to be the best system for developing new polymers and for production of filament. The EX6 features a three-stage extrusion screw made from hardened and polished high-carbon stainless steel. The screw can be easily removed for cleaning and can be swapped out with the various other screw profiles to match the processing requirements of the polymer. With this new system, screws with different characteristics can be used as needed for each specific polymer, allowing screw designs to be tested and polymer output and consistency optimized. All screws have a 24:1 L/D ratio giving greater versatility and control compared to other extruders.



Extrudable Plastics: ABS, ABS Flame Retardant, 4043D PLA, 3D850 PLA, 3D870 PLA, PC, HIPS, PETG, and WAX. Lower Melt Flow Polymers

Extrusion Rate: Over 2 pounds of filament per hour (About 250 inches per minute using 4043D PLA @ 1.75mm)

Filament Sizes: 1.75mm and 2.85mm

Material Input Size: 1/8th of an inch pellets to powder

Material Capacity:  Hopper Volume - approximately 26 cubic inches
Screw Void - 1.75 cubic inches

Temperature Control: PID Controller, One Zone

Feed Screw and Drive:

0-35rpm Speed Control

85in lbs drive force

General Purpose Custom Designed Feed Screw

Non- Removable

Universal Power Input: 110 VAC or 220 VAC - 50 to 60hz - 500 watts

Physical Characteristics: Weight 28 lbs (12.7kg) and dimensions of 18in x 7in x 9in



Extrudable Plastics: 4043D PLA, 3D870 PLA, 3D850 PLA, Magnum 8391 ABS, and HIPS. Click here for EX6 Extrusion settings. The EX6 is also capable of processing ABS Flame Retardant, PC, PP, PS, ULTEM, PEEK, NYLON, HDPE, PETG, and WAX. Low to Higher Melt Flow Polymers. If you don't see a material listed send us a sample we can test. Click here to see our testing services.

Extrusion Rate: Over 10 pounds per hour (4.5kg per hour)

Filament Sizes: 1.75mm and 2.85mm

Material Input Size: 1/8in (3.18mm) pellets to powder

Material Capacity: Hopper - 195 cubic in (3195.5 cubic cm)
Screw Void - 2.37cubic in (38.8 cubic cm)
Feed Port - 195 cubic in (3195.5 cubic cm)

Temperature Control: 4 Independently PID controlled heat zones, all with active fan cooling for consistent heating

Feed Screw and Drive:

0-100rpm Speed Control

24:1 L:D Ratio Screw

16.28" Length (45.31cm)

5/8” Diameter (16mm)

1/2” Pitch (13mm)

Removable and upgradable screw

17-4 PH Stainless Steel and Hardened to Condition H900



90 Day Warranty

**Voltage Note - the 110VAC or 220VAC specific to the country that you are going to be using the extruder system in. There is no operational difference between the 110VAC or 220VAC.**

Click Here for the Filabot EX2 Extruder Manual

Click Here for the Filabot EX6 Extruder Manual

Click Here for the Ink Bird Temperature Control Manual

Reviews here